JB/T 2001.5-1999 Types and dimensions of copper gaskets for water system flanges
Basic Information
Standard ID:
JB/T 2001.5-1999
Standard Name: Types and dimensions of copper gaskets for water system flanges
Chinese Name:
水系统 法兰铜垫 型式与尺寸
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-06-28
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Fluid systems and general parts >> 23.100 Fluid power systems
Standard Classification Number:Machinery>>General Parts>>J20 Hydraulic and Pneumatic Devices
Publication information
other information
Focal point unit:Metallurgical Equipment Standardization Technical Committee
Introduction to standards:
JB/T 2001.5-1999 JB/T 2001.5-1999 Types and dimensions of copper gaskets for flanges in water systems JB/T2001.5-1999 Standard download decompression password: www.bzxz.net
Some standard content:
IC.s$ 23.110
Machinery Industry Standard of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
State Machinery Industry Bureau
2(-01-U1 Implementation
Machinery Industry Standard of the People's Republic of China
Water system flange copper washer
Type and size
Waller system-Plangc copperwasherType and size
This standard specifies the types and sizes of copper plates. H/T2001.5-1999
12G0—34
This standard applies to [200L6-20012—1999 Attachment 3 JDT200114-20018-189 Report "Use in the Form of
Cited Standards
The following standards contain texts, and when they are used in this standard and become the standard version of this standard, the size shown is valid. The standard will be revised. The use of the standards should be considered as follows: The latest version of the listed standards may be JD.T2001.6-2001.12.--1959
Connecting flange
JB.T2001.14.-2001.18.-1999
3 Types and dimensions
3. [The type and size of the stopper of the gasket and the starter shall comply with the provisions of Figure and Table 1. kwww.bzxz.net
3.2 Gasket Finance Department: T3.
Approved by the State Machinery Industry Bureau on June 28, 1999
Implementation on January 1, 2000
TH:1 5
JHI IS:
JB:T2O15.3
JB.T 2401.5 4
2TVT 2001 5.5
1:20015.6
JB:T 2COI 5.:
JR:T 2COI.SS
: 2m :5.9
11:1 2:X:1.3.11
JB/1 7x1.5.12
JB 2X1513
JB/T20G].5.14
JE 20C :.15
D/T 20x:1.5.15
O3:T 2301.5.17
JB 201.5.18
JB-T 2(C1.5.12
JB/T 2(C1.5.21
JB/T 20X.1.5.22
15-1 2x: 1 5.11
1M1Z1:.74
JB/T 2001476
JB2K :27
J3/7 2001.5.28
J2T 2001.$.29
Ji1 2n01..31
4 Marking example
JB/T2001.5—199↓
d. is 13.5 mm, d9.5 mm, 2 mm pad [3.5.9.>-2JB/T2001999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.